To Becker websiteUsage recommendation
- Articulated-arm cassette awning
- Open/semi-open articulated-arm awning
Certifications
... For the user:
Fabric untensioning can be switched on/off in the upper limit position
Higher closing force for cassette awnings
Optional activation: Fabric tensioning function
Made in Germany - for maximum reliability and durability
Blockage detection in both directions with automatic reversal and multiple testing
... For installation:
Automatic shading solution length adjustment
Limit positions status indicator (LSI) signals missing limit positions
Intelligent installation management permits limit position corrections
Switchable stop behaviour
Auto-install function
Setting limit positions: Automatic detection with existing upper stop and fixed point lower limit position programming
Setting of limit positions via switch on the drive head without the need for a special programming unit
... For planning:
Electronic limit switching
Supports parallel connection
After operation in an emergency, the drive finds its limit positions again independently
C-Plug pluggable connecting cable
General product data
Series
E33
Designation
R30-17-E33
Item number
2030 130 187 0
GTIN
4251852915936
Sales unit
pc.
RRP (incl. VAT)
373,00 €
Drive diameter
Ø 45mm = R
Technical data
Weight
2.831 kg
IP degree of protection
44
Mains frequency
50 Hz
Colour
White (RAL 9016)
Speed (load)
14 U/min
Rated current
0.9 A
Power consump.
210 W
Power supply (AC/DC)
Alternating current
Rated voltage
230 V
Duty cycle
S2 4 min
Drive torque (Nm)
30 Nm
Speed (rpm)
17 U/min
Cable type
plug-in
Dimensions
Dimension L1
530 mm
Dimension L2
547 mm
Dimension L3
564 mm
Dimension L4
17 mm
Dimension L5
17 mm
Dimension Ø c
45 mm
Dimensional drawing
Drive adapter width from Drive adapter DW78 R+F diecast (4930 300 091 0), when selecting a different drive adapter, the dimensions L2, L3 and L5 will change
Special features
Suitable for connection in parallel
Motor head can be overwrapped
Obstacle detection
Blockage detection in both directions
Commissioning
Higher closing force can be set
Limit position programming
Intelligent installation management (3x approach)
LSI - limit positions status indicator
Additional features
Soft stop upper limit position
7-Stage - stage 5
Drive can be operated by wired operator control
Fabric untensioning - reversal at the retracted stop- factory default
Fabric untensioning - reversal at the retracted stop
5° - can be activated/deactivated at any time
Assembly and operating instructions
Declarations of conformity
Miscellaneous
Problem:
Tubular drive overruns the limit position or stops short of the set limit position.
Remedy:
Tubular drive does not run in the right direction.
Remedy:
The tubular drive does not retract after setting the extended limit position.
Remedy:
Tubular drive overruns the limit position or stops short of the set limit position.
Remedy:
- Check electrical installation, remove external devices, delete limit positions and then reset limit positions.
- Repair electrical installation and re-program limit positions.
- Stops have broken off or one or several attachments are broken. Repair system; reset tubular drive, then re-program limit positions.
____________________________________________
____________________________________________
Tubular drive does not run in the right direction.
Remedy:
- Tubular drive is overheated. The tubular drive is operational again after a few minutes.
- Tubular drive is faulty (does not run even after standing still for a long period of time). Replace the tubular drive.
- Clear and remove the obstruction and switch in the desired direction. Check the electrical connection.
____________________________________________
The tubular drive does not retract after setting the extended limit position.
Remedy:
- Delete the limit positions, reprogram the outer limit position, and retract immediately.
____________________________________________
* C-plug connecting cables are available in various versions and lengths and must be ordered separately.