To Becker websiteUsage recommendation
- Projection screen
- Roller shutter
- Insect protection
Certifications
As a follow-up/alternative item for this product we recommend:
... For the user:
Soft upper stop – optimum adaptation of closing forces for fabric protection
Enables programming of 2 freely selectable intermediate positions
Memory function: Integrated timer can be activated via MemoControl transmitter
Sensitive obstacle detection in down direction for optimum protection of the application and the obstacle
Fly screen protection function
Dynamic torque adjustment to accommodate changes in the roller shutter element
Upper anti-freeze mechanism with automatic shading solution length adjustment (can be additionally activated)
Made in Germany - for maximum reliability and durability
Automatic increase of the pressing force with anti-lifting devices
Blockage detection in the UP direction (anti-freeze mechanism)
... For installation:
Limit positions status indicator (LSI) signals missing limit positions
Switch on the motor head to change the direction of rotation and to activate and deactivate programming mode
Limit position adjustment: Automatic detection when stop or fixed point end-positions are present
Intelligent installation management permits limit position corrections
Automatic shading solution length adjustment
Automatic detection of the limit positions when flexible suspension springs or rigid shaft connectors are used
... For planning:
C-Plug pluggable connecting cable
Supports parallel connection
Individual, group and central control possible (also by radio)
Integrated radio receiver compatible with the Centronic control unit range
Local operation with a standard single button
General product data
Sales unit
pc.
Item number
2009 120 122 0
Series
C01
Drive diameter
Ø 35mm = P
RRP (incl. VAT)
373,00 €
GTIN
4251852905074
Designation
P9-16-C01 with bracket
Technical data
Power consump.
110 W
Colour
White (RAL 9016)
Speed (load)
13 U/min
Mains frequency
50 Hz
Duty cycle
S2 4 min
Power supply (AC/DC)
Alternating current
IP degree of protection
44
Intermediate positions
2
Weight
1.144 kg
Rated current
0.45 A
Rated voltage
230 V
Drive torque (Nm)
9 Nm
Speed (rpm)
16 U/min
Cable type
plug-in
Dimensions
Dimension L1
453 mm
Dimension L2
493 mm
Dimension L3
506 mm
Dimension L4
13 mm
Dimension L5
40 mm
Dimension Ø c
35 mm
Dimensional drawing
Drive adapter width from Drive adapter S40 for obstruction detection (4930 200 250 0), when selecting a different drive adapter, the dimensions L2, L3 and L5 will change
Special features
Suitable for connection in parallel
Motor head can be overwrapped
Communication
Radio compatibility
Centronic
Obstacle detection
Obstruction detection, sensitive, in the extend direction (drive adapter)
- For roller shutters with rigid shaft connectors
- For roller shutters with springs
Blockage detection in both directions
Commissioning
Reduced drive torque during installation
Limit position programming
Intelligent installation management (3x approach)
Automatic detection of anti-lifting devices
LSI - limit positions status indicator
Fly screen and freeze protection function
Fly screen protection function
140° - can be activated/deactivated
Upper limit position anti-freeze mechanism/shading solution length adjustment
Travel specified - can be activated/deactivated
Upper limit position anti-freeze mechanism/shading solution length adjustment - factory default
Additional features
Intermediate positions
2
Soft stop upper limit position
dynamic
Time function
Memory
Drive can be operated by wired operator control
Time function
Time function
Memory
Assembly and operating instructions
Miscellaneous
selected item
Tubular drive does not run in the right direction.
Remedy:
Problem:
Incorrect running direction after deleting limit positions.
Remedy:
Problem:
Drive is not functioning.
Remedy:
Problem:
During the programming run, the drive stops short of the limit position to be programmed.
Remedy:
Problem:
Ventilation slots of the roller shutter do not close fully.
Remedy:
Problem:
Switching times cannot be set on tubular drive.
Remedy:
____________________________________________
Tubular drive does not run in the right direction.
Remedy:
- Tubular drive is overheated. The tubular drive is operational again after a few minutes.
- Tubular drive is faulty (does not run even after standing still for a long period of time). Replace the tubular drive.
- Clear and remove the obstruction and switch in the desired direction. Check the electrical connection.
____________________________________________
Problem:
Incorrect running direction after deleting limit positions.
Remedy:
- Use the master transmitter or the direction switch on the tubular drive to change the direction of rotation.
____________________________________________
Problem:
Drive is not functioning.
Remedy:
- Program new transmitter.
- Bring transmitter within range of the tubular drive.
- Press drive or stop button on transmitter at least five times in the immediate vicinity of the tubular drive.
- Insert battery/batteries correctly in the transmitter or insert new battery/batteries.
- Check electrical connection.
- Thermal protection switch in tubular drive has tripped. Wait until the thermal protection switch in the tubular drive is reactivated.
Problem:
Running direction on tubular drive cannot be set
Remedy:
Running direction on tubular drive cannot be set
Remedy:
- Delete limit positions and reset the running direction.
____________________________________________
Problem:
During the programming run, the drive stops short of the limit position to be programmed.
Remedy:
- For safety reasons, the drive reacts sensitively to sluggishness during the programming run, in order to prevent damage. Briefly run roller shutter DOWN and then UP until you reach the upper limit position.
____________________________________________
Problem:
Ventilation slots of the roller shutter do not close fully.
Remedy:
- Delete the limit positions (see Deleting limit positions) and then set the limit positions as per to lower point (see chapter Setting the limit positions); in this case, set the lower limit position first (lower point) followed by the upper limit position.
____________________________________________
Problem:
Switching times cannot be set on tubular drive.
Remedy:
- Use Centronic transmitter with Manual/Auto slide switch.
Tubular drive does not operate at the set switching time.
Remedy:
Remedy:
- Switch from Manual to Auto.
- Switch the slide switch on a Centronic transmitter from Manual to Auto. If the slide switch is already at Auto, it will need to be switched to Manual and then back to Auto.
- Switch the slide switch on a Centronic transmitter from Manual to Auto. If the slide switch is already at Auto, it will need to be switched to Manual and then back to Auto.
Problem:
Set switching times change.
Remedy:
Set switching times change.
Remedy:
- Frequent 230 V AC power cuts. Fluctuations in the 50 Hz mains frequency.
- Use a "TimeControl" transmitter and adjust the desired switching time there.
____________________________________________
* C-plug connecting cables are available in various versions and lengths and must be ordered separately.