To Becker websiteUsage recommendation
- Sun protection
- Venetian blind/shutter
- Roller shutter
Integration into Becker CentralControl possible
Compatible with homee smart home system
Two intermediate positions can be programmed
Blind mode: Two intermediate positions (with tilt) can be programmed
Blind mode: Exact adjustment of slat angle possible
Setting the threshold values possible via a programmed operating device
Two memory switching times with daily repetition programmable
Compatible with Centronic und CentronicPlus transmitters and sensors
The device feeds its position or switching state and status information back to the operator unit and gateway
Mesh technology ensures the automatic networking of all devices to create a powerful network
Optional potential-free switching contact
Can be fitted into any flush-mounted device socket with 58 mm diameter according to DIN EN 49073 / DIN EN 60670
Installation behind the operator control in any deep flush-mounted switch box possible
Can be combined with any switch range
Defined drive commands possible
Can be programmed to recognise up to 16 Centronic transmitters
General product data
GTIN
4251852916056
Sales unit
pc.
Item number
4036 000 013 0
Designation
Centronic VarioControl VC520 PLUS
RRP (incl. VAT)
186,00 €
Series
Receiver
Technical data
Can be integrated into the switch frame
no
Weight
0.09 kg
Width
41 mm
Number of channels
1
Type of mounting
Flush mounted
Touch mode
Intermediate positions
2
Length
44 mm
Dimensions
B x H x T: 41 x 44 x 20 mm
Colour
Grey
Power supply (AC/DC)
Alternating current
Switching current max.
µ 3A / 110 240V AC; µ 3 A / 30 V DC
Height/depth
20 mm
IP degree of protection
20
Mains frequency
50/60 Hz
Rated voltage
110 - 240 V
Dimensional drawing
Communication
Bidirectional product
Active participant for routing/meshing
Additional features
Intermediate positions
2
Time function
Memory
Sensor functions
Sensor values - evaluable
- Sun
- Rain
- Wind
Time function
Time function
Memory
Assembly and operating instructions
Declarations of conformity
Miscellaneous
Problem:
Tubular drive/receiver is not responding.
Remedy:
- Insert a new battery/batteries into the hand-held transmitter.
- Make sure the battery/batteries is/are correctly inserted in the hand-held transmitter.
- Reduce distance from receiver.
- Program transmitter.
- Check the receiver.
____________________________________________
Problem:
The LED ring on the hand-held transmitter lights up red when the receiver for the setting mode is selected.
Remedy:
- Reduce distance from receiver.
- Check electr. connection of the receiver.
- Put the receiver into programming mode.
- Add the transmitter to the installation.
____________________________________________
Tubular drive is running in the wrong direction.
Remedy:
Remedy:
- Swap the OPEN and CLOSE wires at the radio receiver.
- Change the direction of rotation via the transmitter.
Problem:
Intermediate positions I/II have moved.
Remedy:
Intermediate positions I/II have moved.
Remedy:
- Set the travel path again and reprogram the intermediate positions I/II.
Problem:
Tubular drive does not operate at the set switching time.
Remedy:
Problem:
Set switching times change.
Remedy:
Problem:
Tubular drive does not operate at the set switching time.
Remedy:
- Switch from Manual to Auto.
- If the slide switch of a Centronic transmitter is already at AUTO, it will need to be switched to MANUAL and then back to AUTO.
Problem:
Set switching times change.
Remedy:
- Frequent 230 V AC power cuts. Fluctuations in the 50 Hz mains frequency. Use a "TimeControl" transmitter and adjust the desired switching time there.
The required setting cannot be changed.
Remedy:
Remedy:
- Make sure that the CentronicPlus transmitter is in setting mode if necessary.
Problem:
Required tubular drive/receiver is not responding.
Remedy:
Required tubular drive/receiver is not responding.
Remedy:
- Program transmitter.
- Select the correct channel on the transmitter.
- Check connection.
- Check the external push-button connection.
____________________________________________
Required tubular drive/receiver is not responding.
Remedy:
- Program transmitter.
- Select the correct channel on the transmitter.
- Check connection.
- Check the external push-button connection.
____________________________________________
LED ring flashes yellow or red 4 times.
Remedy:
- Insert new batteries into the transmitter.
____________________________________________