To Becker websiteUsage recommendation
- Conservatory awning
- Guided
- Volants
- Articulated-arm cassette awning
- Drop-arm awning
- Pergola
- Markisolette/window awning
- Open/semi-open articulated-arm awning
- Horizontal screen
Certifications
... For the user:
The mesh technology allows individual drives to connect together automatically to form a very efficient network
Blockage detection in both directions with automatic reversal and multiple testing
Higher closing force for cassette awnings
Memory function: Integrated timer can be activated via MemoControl transmitter
Wireless software update via DECT central controls, e.g. FRITZ!Box
Made in Germany - for maximum reliability and durability
Enables programming of 2 freely selectable intermediate positions
Compatible with sun/wind/rain sensors for maximum convenience
Fabric untensioning can be switched on/off in the upper limit position
Optional activation: Fabric tensioning function
... For installation:
Lower limit position adjustment: point (automatic detection or freely programmable), Upper limit position adjustment: point or stop
Switchable stop behaviour
Automatic shading solution length adjustment
Switch on the motor head to change the direction of rotation and to activate and deactivate programming mode
Intelligent installation management permits limit position corrections
Limit positions status indicator (LSI) signals missing limit positions
Auto-install function
Convenient threshold adjustment via the hand-held transmitter or central control units
... For planning:
Integrated CentronicPlus radio transceiver: Bidirectional, 868.3 MHz, the drive reports back its position, any blockage and other status information
Individual, group and central control possible (also by radio)
C-Plug pluggable connecting cable
Supports parallel connection
Integrated radio receiver compatible with the Centronic control unit range
Local operation with a standard single button
General product data
RRP (incl. VAT)
522,00 €
Series
C12 PLUS
GTIN
4251852916612
Sales unit
pc.
Item number
2060 130 161 0
Drive diameter
Ø 58mm = L
Designation
L60-11-C12 PLUS
Technical data
IP degree of protection
44
Power supply (AC/DC)
Alternating current
Rated current
1.2 A
Speed (load)
8 U/min
Duty cycle
S2 4 min
Rated voltage
230 V
Weight
4.057 kg
Intermediate positions
2
Power consump.
265 W
Mains frequency
50 Hz
Colour
White (RAL 9016)
Drive torque (Nm)
60 Nm
Speed (rpm)
11 U/min
Cable type
plug-in
Dimensions
Dimension L1
533.8 mm
Dimension L2
563.8 mm
Dimension L3
583.8 mm
Dimension L4
20 mm
Dimension L5
30 mm
Dimension Ø c
58 mm
Dimensional drawing
Drive adapter width from Drive adapter DW78N 1.5 mm centre offset (4931 300 365 0), when selecting a different drive adapter, the dimensions L2, L3 and L5 will change
Special features
Suitable for connection in parallel
Motor head can be overwrapped
Communication
Bidirectional product
Active participant for routing/meshing
Radio compatibility
- Centronic
- Centronic PLUS
Obstacle detection
Blockage detection in both directions
Commissioning
Higher closing force can be set
Limit position programming
Intelligent installation management (3x approach)
LSI - limit positions status indicator
Additional features
Intermediate positions
2
Soft stop upper limit position
7-Stage - stage 5
Time function
Memory
Drive can be operated by wired operator control
Fabric untensioning - reversal at the retracted stop- factory default
Fabric untensioning - reversal at the retracted stop
5° - can be activated/deactivated at any time
Sensor functions
Sensor values - evaluable
- Sun
- Wind
- Rain
- Frost
- Twilight
- Temperature
Time function
Time function
Memory
Assembly and operating instructions
Declarations of conformity
Miscellaneous
selected item
Tubular drive does not run in the right direction.
Remedy:
Problem:
Drive is not functioning.
Remedy:
Problem:
Incorrect running direction after deleting limit positions.
Remedy:
Problem:
The LED ring lights up red when the receiver for the setting mode is selected.
Remedy:
Problem:
During the programming run, the drive stops short of the limit position to be programmed.
Remedy:
____________________________________________
Tubular drive does not run in the right direction.
Remedy:
- Tubular drive is overheated. The tubular drive is operational again after a few minutes.
- Tubular drive is faulty (does not run even after standing still for a long period of time). Replace the tubular drive.
- Clear and remove the obstruction and switch in the desired direction. Check the electrical connection.
____________________________________________
Problem:
Drive is not functioning.
Remedy:
- Program new transmitter.
- Bring transmitter within range of the tubular drive.
- Press drive or stop button on transmitter at least five times in the immediate vicinity of the tubular drive.
- Insert battery/batteries correctly in the transmitter or insert new battery/batteries.
- Check electrical connection.
- Thermal protection switch in tubular drive has tripped. Wait until the thermal protection switch in the tubular drive is reactivated.
Problem:
Running direction on tubular drive cannot be set
Remedy:
Running direction on tubular drive cannot be set
Remedy:
- Delete limit positions and reset the running direction.
____________________________________________
Problem:
Incorrect running direction after deleting limit positions.
Remedy:
- Use the relevant transmitter or the direction switch on the tubular drive to change the direction of rotation.
____________________________________________
Problem:
The LED ring lights up red when the receiver for the setting mode is selected.
Remedy:
- Reduce the distance from the receiver.
- Check the electrical connection of the receiver.
- Put the receiver into programming mode.
- Add the transmitter to the installation.
Problem:
The required setting cannot be changed.
Remedy:
The required setting cannot be changed.
Remedy:
- Make sure that the CentronicPlus transmitter is in programming mode.
____________________________________________
Problem:
During the programming run, the drive stops short of the limit position to be programmed.
Remedy:
- For safety reasons, the drive reacts sensitively to sluggishness during the programming run, in order to prevent damage. Briefly run roller shutter DOWN and then UP until you reach the upper limit position.
____________________________________________
* C-plug connecting cables are available in various versions and lengths and must be ordered separately.