To Becker websiteUsage recommendation
- Roller shutter
- Projection screen
Certifications
... For the user:
Soft upper stop – optimum adaptation of closing forces for fabric protection
Automatic increase of the pressing force with anti-lifting devices
Upper anti-freeze mechanism with automatic shading solution length adjustment (can be additionally activated)
Sensitive obstacle detection in down direction for optimum protection of the application and the obstacle
Fly screen protection function
Enables programming of 2 freely selectable intermediate positions
Blockage detection in the UP direction (anti-freeze mechanism)
Dynamic torque adjustment to accommodate changes in the roller shutter element
Made in Germany - for maximum reliability and durability
... For installation:
Adjustable direction of rotation
Limit position adjustment: Automatic detection when stop or fixed point end-positions are present
Automatic detection of the limit positions when flexible suspension springs or rigid shaft connectors are used
Limit positions status indicator (LSI) signals missing limit positions
Automatic shading solution length adjustment
Intelligent installation management permits limit position corrections
... For planning:
Supports parallel connection
Integrated SMI technology
C-Plug pluggable connecting cable
General product data
Sales unit
pc.
Series
S01
Designation
R20-17-S01
Item number
2020 120 502 0
RRP (incl. VAT)
373,00 €
Drive diameter
Ø 45mm = R
GTIN
4251852906897
Technical data
Weight
2 kg
Power supply (AC/DC)
Alternating current
Rated current
0.7 A
Duty cycle
S2 4 min
Colour
White (RAL 9016)
Intermediate positions
2
Power consump.
160 W
Mains frequency
50 Hz
IP degree of protection
44
Speed (load)
14 U/min
Rated voltage
230 V
Drive torque (Nm)
20 Nm
Speed (rpm)
17 U/min
Cable type
plug-in
Dimensions
Dimension L1
501.95 mm
Dimension L2
541.95 mm
Dimension L3
558.95 mm
Dimension L4
17 mm
Dimension L5
40 mm
Dimension Ø c
45 mm
Dimensional drawing
Drive adapter width from Drive adapter S60 for obstruction detection (4930 200 222 0), when selecting a different drive adapter, the dimensions L2, L3 and L5 will change
Special features
Suitable for connection in parallel
Motor head can be overwrapped
Communication
Bidirectional product
Obstacle detection
Obstruction detection, sensitive, in the extend direction (drive adapter)
- For roller shutters with springs
- For roller shutters with rigid shaft connectors
Blockage detection in both directions
Commissioning
Reduced drive torque during installation
Limit position programming
Intelligent installation management (3x approach)
Automatic detection of anti-lifting devices
LSI - limit positions status indicator
Fly screen and freeze protection function
Fly screen protection function
140° - can be activated/deactivated
Upper limit position anti-freeze mechanism/shading solution length adjustment
Travel specified - can be activated/deactivated
Upper limit position anti-freeze mechanism/shading solution length adjustment - factory default
Additional features
Intermediate positions
2
Soft stop upper limit position
dynamic
Assembly and operating instructions
Declarations of conformity
Miscellaneous
Problem:
Tubular drive does not run in the right direction.
Remedy:
Tubular drive does not run in the right direction.
Remedy:
Tubular drive overruns the limit position or stops short of the set limit position.
Remedy:
Problem:
The tubular drive does not function correctly in SMI mode.
Remedy:
Problem:
During the programming run, the drive stops short of the limit position to be programmed.
Remedy:
Problem:
Ventilation slots of the roller shutter do not close fully.
Remedy:
Tubular drive does not run in the right direction.
Remedy:
- Tubular drive is overheated. The tubular drive is operational again after a few minutes.
- Tubular drive is faulty (does not run even after standing still for a long period of time). Replace the tubular drive.
- Clear and remove the obstruction and switch in the desired direction. Check the electrical connection.
____________________________________________
____________________________________________
Tubular drive does not run in the right direction.
Remedy:
- Tubular drive is overheated. The tubular drive is operational again after a few minutes.
- Tubular drive is faulty (does not run even after standing still for a long period of time). Replace the tubular drive.
- Clear and remove the obstruction and switch in the desired direction. Check the electrical connection.
____________________________________________
Tubular drive overruns the limit position or stops short of the set limit position.
Remedy:
- Check electrical installation, remove external devices, delete limit positions and then reset limit positions.
- Repair electrical installation and re-program limit positions.
- Stops have broken off or one or several attachments are broken. Repair system; reset tubular drive, then re-program limit positions.
____________________________________________
Problem:
The tubular drive does not function correctly in SMI mode.
Remedy:
- Check the electrical connection.
Problem:
In BUS mode, the tubular drive extends the sun protection device with retraction commands or retracts it with extension commands.
Remedy:
In BUS mode, the tubular drive extends the sun protection device with retraction commands or retracts it with extension commands.
Remedy:
- Disconnect the tubular drive from the SMI BUS. Delete the limit positions, switch the direction switch to the opposite position and test the direction of travel with the programming unit. Re-program the limit positions.
____________________________________________
Problem:
During the programming run, the drive stops short of the limit position to be programmed.
Remedy:
- For safety reasons, the drive reacts sensitively to sluggishness during the programming run, in order to prevent damage. Briefly run roller shutter DOWN and then UP until you reach the upper limit position.
____________________________________________
Problem:
Ventilation slots of the roller shutter do not close fully.
Remedy:
- Delete the limit positions (see Deleting limit positions) and then set the limit positions as per to lower point (see chapter Setting the limit positions); in this case, set the lower limit position first (lower point) followed by the upper limit position.
____________________________________________
* C-plug connecting cables are available in various versions and lengths and must be ordered separately.