To Becker websiteUsage recommendation
- Venetian blind/shutter
- Roller shutter
- Sun protection
Integration into Becker CentralControl possible
Compatible with homee smart home system
Two intermediate positions can be programmed
Blind mode: Two intermediate positions (with tilt) can be programmed
Blind mode: Exact adjustment of slat angle possible
Setting the threshold values possible via a programmed operating device
Two memory switching times with daily repetition programmable
Compatible with Centronic und CentronicPlus transmitters and sensors
The device feeds its position or switching state and status information back to the operator unit and gateway
Mesh technology ensures the automatic networking of all devices to create a powerful network
An additional operator control can be connected
Can be fitted into any flush-mounted device socket with 58 mm diameter according to DIN EN 49073 / DIN EN 60670
Installation behind the operator control in any deep flush-mounted switch box possible
Can be combined with any switch range
Defined drive commands possible
Can be programmed to recognise up to 16 Centronic transmitters
General product data
Designation
Centronic VarioControl VC420 PLUS
GTIN
4251852908716
Item number
4036 000 008 0
Sales unit
pc.
Series
Receiver
RRP (incl. VAT)
152,00 €
Technical data
Width
40 mm
Colour
Grey
Intermediate positions
2
Dimensions
B x H x T: 40 x 42 x 20 mm
Switching current max.
µ 3A / 110-240V / AC cos Φ = 1
Number of channels
1
Length
42.5 mm
Weight
0.09 kg
Type of mounting
Flush mounted
Height/depth
19.5 mm
IP degree of protection
20
Can be integrated into the switch frame
no
Mains frequency
50 Hz
Power supply (AC/DC)
Alternating current
Rated voltage
110 - 240 V
Dimensional drawing
Communication
Bidirectional product
Active participant for routing/meshing
Additional features
Intermediate positions
2
Time function
Memory
Sensor functions
Sensor values - evaluable
- Rain
- Wind
- Sun
Time function
Time function
Memory
Assembly and operating instructions
Declarations of conformity
Miscellaneous
Problem:
Tubular drive/receiver is not responding.
Remedy:
- Insert a new battery/batteries into the hand-held transmitter.
- Make sure the battery/batteries is/are correctly inserted in the hand-held transmitter.
- Reduce distance from receiver.
- Program transmitter.
- Check the receiver.
____________________________________________
Problem:
The LED ring on the hand-held transmitter lights up red when the receiver for the setting mode is selected.
Remedy:
- Reduce distance from receiver.
- Check electr. connection of the receiver.
- Put the receiver into programming mode.
- Add the transmitter to the installation.
____________________________________________
Tubular drive is running in the wrong direction.
Remedy:
Remedy:
- Swap the OPEN and CLOSE wires at the radio receiver.
- Change the direction of rotation via the transmitter.
Problem:
Intermediate positions I/II have moved.
Remedy:
Intermediate positions I/II have moved.
Remedy:
- Set the travel path again and reprogram the intermediate positions I/II.
Problem:
Tubular drive does not operate at the set switching time.
Remedy:
Problem:
Set switching times change.
Remedy:
Problem:
Tubular drive does not operate at the set switching time.
Remedy:
- Switch from Manual to Auto.
- If the slide switch of a Centronic transmitter is already at AUTO, it will need to be switched to MANUAL and then back to AUTO.
Problem:
Set switching times change.
Remedy:
- Frequent 230 V AC power cuts. Fluctuations in the 50 Hz mains frequency. Use a "TimeControl" transmitter and adjust the desired switching time there.
The required setting cannot be changed.
Remedy:
Remedy:
- Make sure that the CentronicPlus transmitter is in setting mode if necessary.
Problem:
Required tubular drive/receiver is not responding.
Remedy:
Required tubular drive/receiver is not responding.
Remedy:
- Program transmitter.
- Select the correct channel on the transmitter.
- Check connection.
- Check the external push-button connection.
____________________________________________
Required tubular drive/receiver is not responding.
Remedy:
- Program transmitter.
- Select the correct channel on the transmitter.
- Check connection.
- Check the external push-button connection.
____________________________________________